# Top

**URL:** https://discuss.px4.io/top.md

[Latest](https://discuss.px4.io/latest.md) · [Categories](https://discuss.px4.io/categories.md)

---

## [Large QuadCopter Oscillates when takeoff](https://discuss.px4.io/t/large-quadcopter-oscillates-when-takeoff/49689)

<div class="topic-metadata">

**Author:** [@Hiran\_Bandarigoda](https://discuss.px4.io/u/Hiran_Bandarigoda)\
**Replies:** 16\
**Last updated:** [November 8, 2026, 4:00pm UTC](https://discuss.px4.io/t/large-quadcopter-oscillates-when-takeoff/49689 "2026-11-08T16:00:41Z")

</div>

So I have been flying this drone for some time now. Last Friday I flew it a couple of flights and had no issue. But today it suddenly started to Oscillate after taking off around 1m. I checked everything and all are tigh…

---

## [Set home position in flight](https://discuss.px4.io/t/set-home-position-in-flight/49698)

<div class="topic-metadata">

**Author:** [@nickfil](https://discuss.px4.io/u/nickfil)\
**Replies:** 14\
**Last updated:** [November 17, 2026, 12:36am UTC](https://discuss.px4.io/t/set-home-position-in-flight/49698 "2026-11-17T00:36:10Z")

</div>

Hi all, I have noticed that the option to ‘Set home position’ in flight does not change anything (wiht qgc: press on a point on the map and then the option to set home here appears). This is supported by the fact that …

---

## [Battery resistance estimate reaches zero and persists under load (FMUv6C, BAT1\_R\_INTERNAL=-1)](https://discuss.px4.io/t/battery-resistance-estimate-reaches-zero-and-persists-under-load-fmuv6c-bat1-r-internal-1/49724)

<div class="topic-metadata">

**Author:** [@ahmet\_arif\_altintas](https://discuss.px4.io/u/ahmet_arif_altintas)\
**Replies:** 17\
**Last updated:** [November 16, 2026, 1:42am UTC](https://discuss.px4.io/t/battery-resistance-estimate-reaches-zero-and-persists-under-load-fmuv6c-bat1-r-internal-1/49724 "2026-11-16T01:42:17Z")

</div>

Hi PX4 developers, Could you help review a battery-estimator behavior observed on one multicopter using the PX4\_FMU\_V6C target? During flight, the published per-cell battery\_status.internal\_resistance\_estimate becomes…

---

## [Multicopter on PX4 v1.16 or older? Your u-blox likely runs dynamic model 6, which added about 46 ms of GPS lag on public logs (and 104 ms on PR #24831's test vehicle)](https://discuss.px4.io/t/multicopter-on-px4-v1-16-or-older-your-u-blox-likely-runs-dynamic-model-6-which-added-about-46-ms-of-gps-lag-on-public-logs-and-104-ms-on-pr-24831s-test-vehicle/49705)

<div class="topic-metadata">

**Author:** [@munimv2](https://discuss.px4.io/u/munimv2)\
**Replies:** 13\
**Last updated:** [November 13, 2026, 5:52am UTC](https://discuss.px4.io/t/multicopter-on-px4-v1-16-or-older-your-u-blox-likely-runs-dynamic-model-6-which-added-about-46-ms-of-gps-lag-on-public-logs-and-104-ms-on-pr-24831s-test-vehicle/49705 "2026-11-13T05:52:43Z")

</div>

Hi all, this is MV2 of Munim, Inc. We’ve been measuring how far each PX4 vehicle’s GPS lags its IMU from flight logs, and comparing that with the delay EKF2 assumes (EKF2\_GPS\_DELAY, or SENS\_GPSn\_DELAY from v1.18). One se…

---

## [Building Highspeed Rocket shaped drone using Pixhawk 2.4.8](https://discuss.px4.io/t/building-highspeed-rocket-shaped-drone-using-pixhawk-2-4-8/49763)

<div class="topic-metadata">

**Author:** [@shanks](https://discuss.px4.io/u/shanks)\
**Replies:** 9\
**Last updated:** [November 17, 2026, 8:27am UTC](https://discuss.px4.io/t/building-highspeed-rocket-shaped-drone-using-pixhawk-2-4-8/49763 "2026-11-17T08:27:49Z")

</div>

I am currently researching a high-speed, rocket-shaped VTOL UAV and would like some guidance regarding flight-controller compatibility. Can the Pixhawk 2.4.8 support an unconventional airframe of this type? I would also …

---

## [PX4 1.12.6 + AirSim lockstep: with 50 drones, 30Hz step is rejected by PX4 but 10ms step may be too heavy — how to configure?](https://discuss.px4.io/t/px4-1-12-6-airsim-lockstep-with-50-drones-30hz-step-is-rejected-by-px4-but-10ms-step-may-be-too-heavy-how-to-configure/49862)

<div class="topic-metadata">

**Author:** [@24553457](https://discuss.px4.io/u/24553457)\
**Replies:** 14\
**Last updated:** [November 21, 2026, 6:52am UTC](https://discuss.px4.io/t/px4-1-12-6-airsim-lockstep-with-50-drones-30hz-step-is-rejected-by-px4-but-10ms-step-may-be-too-heavy-how-to-configure/49862 "2026-11-21T06:52:07Z")

</div>

Environment: PX4 1.12.6 + AirSim, lockstep enabled (SteppableClock), targeting 30–50 drones simultaneously. Lockstep is mandatory because I need speed-up and pause. Problem: With step-ns = 10ms (100Hz), drones take o…

---

## [FPV camera aspect ratio](https://discuss.px4.io/t/fpv-camera-aspect-ratio/49632)

<div class="topic-metadata">

**Author:** [@alexander.m.frank](https://discuss.px4.io/u/alexander.m.frank)\
**Replies:** 9\
**Last updated:** [November 1, 2026, 12:44pm UTC](https://discuss.px4.io/t/fpv-camera-aspect-ratio/49632 "2026-11-01T12:44:55Z")

</div>

Hi. I have camera which is 640x480, but perhaps has non-square pixels, and thus gives 16:9 picture. Apps like USB camera, Cheese etc. show all correctly. As for QGC it shows 4:3 picture and completely ignores aspect rati…

---

## [PX4 Dev Call: Nov 18, 2026 (Team sync, and Community Q&A)](https://discuss.px4.io/t/px4-dev-call-nov-18-2026-team-sync-and-community-q-a/49970)

<div class="topic-metadata">

**Author:** [@system](https://discuss.px4.io/u/system)\
**Replies:** 1\
**Last updated:** [November 18, 2026, 10:59am UTC](https://discuss.px4.io/t/px4-dev-call-nov-18-2026-team-sync-and-community-q-a/49970 "2026-11-18T10:59:30Z")

</div>

PX4 Sync / Q&A - 2026-11-18T16:00:00Z (UTC) This week: 42 PRs merged | 231 awaiting review | 0 new bugs Announcements Events Dev Call Items None Release Updates: Pre-release rc2 was shipped and submitted to …

---

## [PX4 Dev Call: Nov 04, 2026 (Team sync, and Community Q&A)](https://discuss.px4.io/t/px4-dev-call-nov-04-2026-team-sync-and-community-q-a/49687)

<div class="topic-metadata">

**Author:** [@system](https://discuss.px4.io/u/system)\
**Replies:** 1\
**Last updated:** [November 3, 2026, 1:49am UTC](https://discuss.px4.io/t/px4-dev-call-nov-04-2026-team-sync-and-community-q-a/49687 "2026-11-03T01:49:13Z")

</div>

PX4 Sync / Q&A - 2026-11-04T16:00:00Z (UTC) This week: 132 PRs merged | 182 awaiting review | 0 new bugs Announcements PX4 Developer Summit Minneapolis Videos Events Dev Call Items None Release Updates: There …

---

## [QGC 5.1.5: ArduPlane 4.7.x log downloads ~6× slower than direct MAVFTP](https://discuss.px4.io/t/qgc-5-1-5-arduplane-4-7-x-log-downloads-6x-slower-than-direct-mavftp/49633)

<div class="topic-metadata">

**Author:** [@boi](https://discuss.px4.io/u/boi)\
**Replies:** 7\
**Last updated:** [October 28, 2026, 12:30pm UTC](https://discuss.px4.io/t/qgc-5-1-5-arduplane-4-7-x-log-downloads-6x-slower-than-direct-mavftp/49633 "2026-10-28T12:30:35Z")

</div>

Love the SW, thanks for the work you do. My assistant drafted this report about a large log I just downloaded. found what appears to be an unnecessary fallback from MAVFTP to the legacy MAVLink log-download protocol. T…

---

## [Would the tests notice a planted change in the MAVLink C parser?](https://discuss.px4.io/t/would-the-tests-notice-a-planted-change-in-the-mavlink-c-parser/49638)

<div class="topic-metadata">

**Author:** [@Yannik\_w](https://discuss.px4.io/u/Yannik_w)\
**Replies:** 8\
**Last updated:** [November 1, 2026, 1:10pm UTC](https://discuss.px4.io/t/would-the-tests-notice-a-planted-change-in-the-mavlink-c-parser/49638 "2026-11-01T13:10:46Z")

</div>

Hi all, I ran a small experiment on the MAVLink C parser (c\_library\_v2, commit 56f6435e). I planted 40 small changes into the code and checked which of them the existing tests notice. 22 were noticed and 18 were missed, …

---

## [DShot turtle recovery for PX4 — working implementation, demo and upstream discussion](https://discuss.px4.io/t/dshot-turtle-recovery-for-px4-working-implementation-demo-and-upstream-discussion/49742)

<div class="topic-metadata">

**Author:** [@yisrael-benshlomo](https://discuss.px4.io/u/yisrael-benshlomo)\
**Replies:** 8\
**Last updated:** [November 18, 2026, 6:38pm UTC](https://discuss.px4.io/t/dshot-turtle-recovery-for-px4-working-implementation-demo-and-upstream-discussion/49742 "2026-11-18T18:38:27Z")

</div>

We developed configurable turtle recovery for PX4 during our Dragonfly project and have released the implementation as open source. Dragonfly is a 2.5-inch guarded Quad-X built for indoor flying. A collision near an obs…

---

## [Pixhawk 2.4.8 B-Cube - Power redundancy not met (brick\_valid - 0)](https://discuss.px4.io/t/pixhawk-2-4-8-b-cube-power-redundancy-not-met-brick-valid-0/49678)

<div class="topic-metadata">

**Author:** [@jeffn1](https://discuss.px4.io/u/jeffn1)\
**Replies:** 3\
**Last updated:** [November 8, 2026, 9:02pm UTC](https://discuss.px4.io/t/pixhawk-2-4-8-b-cube-power-redundancy-not-met-brick-valid-0/49678 "2026-11-08T21:02:39Z")

</div>

Pixhawk 2.4.8 B-Cube - Power redundancy not met (brick\_valid - 0) PX4\_FMU\_V3 I am seeking help with a persistent power redundancy warning on my OPixhawk 2.4.8 Cube flight controller. Two Pixhawk controller both reporti…

---

## [Too Fast motor spin when arming](https://discuss.px4.io/t/too-fast-motor-spin-when-arming/49788)

<div class="topic-metadata">

**Author:** [@Andrew\_Kim](https://discuss.px4.io/u/Andrew_Kim)\
**Replies:** 4\
**Last updated:** [November 16, 2026, 7:56am UTC](https://discuss.px4.io/t/too-fast-motor-spin-when-arming/49788 "2026-11-16T07:56:05Z")

</div>

Amax 2312 motor Zex 80A ESC ark fpv flight contoller I think I set up the drone for initial flight correctly, but when the arming or motor test slide is set to the minimum, the motor speed is too fast. Even without ra…

---

## [TALOS HUB: Autonomous Flight and Pilot Assistance](https://discuss.px4.io/t/talos-hub-autonomous-flight-and-pilot-assistance/49682)

<div class="topic-metadata">

**Author:** [@taloshub.project](https://discuss.px4.io/u/taloshub.project)\
**Replies:** 8\
**Last updated:** [November 7, 2026, 2:48pm UTC](https://discuss.px4.io/t/talos-hub-autonomous-flight-and-pilot-assistance/49682 "2026-11-07T14:48:48Z")

</div>

Hello everyone, I’m a model aviation and flying enthusiast, and for some time I’ve been studying, designing and developing a software system for autonomous flight and pilot assistance. It is intended to coordinate missi…

---

## [Adding a heavier payload without ruining flight time](https://discuss.px4.io/t/adding-a-heavier-payload-without-ruining-flight-time/49762)

<div class="topic-metadata">

**Author:** [@3362912101](https://discuss.px4.io/u/3362912101)\
**Replies:** 5\
**Last updated:** [November 15, 2026, 12:00pm UTC](https://discuss.px4.io/t/adding-a-heavier-payload-without-ruining-flight-time/49762 "2026-11-15T12:00:06Z")

</div>

I’m building a drone to carry a camera payload, but once i add the camera, mounting hardware, and extra electronics, the weight adds up quickly. How do you guys calculate whether a frame and motor setup can handle the ex…

---

## [Open source tool that builds per-aircraft maintenance and operations records from PX4 ULogs (feedback welcome)](https://discuss.px4.io/t/open-source-tool-that-builds-per-aircraft-maintenance-and-operations-records-from-px4-ulogs-feedback-welcome/49660)

<div class="topic-metadata">

**Author:** [@tornidomaroc-web](https://discuss.px4.io/u/tornidomaroc-web)\
**Replies:** 5\
**Last updated:** [November 4, 2026, 5:27am UTC](https://discuss.px4.io/t/open-source-tool-that-builds-per-aircraft-maintenance-and-operations-records-from-px4-ulogs-feedback-welcome/49660 "2026-11-04T05:27:36Z")

</div>

Hi all, I have been building an open source workbench for small civil fleets. It builds maintenance and operations records from the flight logs operators already have. I would like feedback from people who work with ULo…

---

## [Hobbywing X6 SE Reports Wrong RPM](https://discuss.px4.io/t/hobbywing-x6-se-reports-wrong-rpm/49755)

<div class="topic-metadata">

**Author:** [@Hiran\_Bandarigoda](https://discuss.px4.io/u/Hiran_Bandarigoda)\
**Replies:** 6\
**Last updated:** [November 16, 2026, 4:53pm UTC](https://discuss.px4.io/t/hobbywing-x6-se-reports-wrong-rpm/49755 "2026-11-16T16:53:50Z")

</div>

Hi, I’m using https://www.hobbywing.com/en/products/cmx6se motors, X6 SE-280KV. I used UAVCAN to get the RPM data from the motors, but the RPM it shows is higher than actual. Datasheet maximum is around 5000RPM while t…

---

## [What problems did you hit when connecting learned/AI-based modules to PX4 in real flights?](https://discuss.px4.io/t/what-problems-did-you-hit-when-connecting-learned-ai-based-modules-to-px4-in-real-flights/49844)

<div class="topic-metadata">

**Author:** [@Onur\_Genc](https://discuss.px4.io/u/Onur_Genc)\
**Replies:** 8\
**Last updated:** [November 21, 2026, 12:24am UTC](https://discuss.px4.io/t/what-problems-did-you-hit-when-connecting-learned-ai-based-modules-to-px4-in-real-flights/49844 "2026-11-21T00:24:24Z")

</div>

Hi all, I’m a solo founder working on drone autonomy and trying to learn from people with real flight experience (not selling anything). So far I’ve worked mostly in PX4 SITL/Gazebo, so I’m especially interested in what …

---

## [Can geofence max distance be set greater than 10000m?](https://discuss.px4.io/t/can-geofence-max-distance-be-set-greater-than-10000m/49647)

<div class="topic-metadata">

**Author:** [@lt.uk](https://discuss.px4.io/u/lt.uk)\
**Replies:** 4\
**Last updated:** [October 28, 2026, 9:45pm UTC](https://discuss.px4.io/t/can-geofence-max-distance-be-set-greater-than-10000m/49647 "2026-10-28T21:45:34Z")

</div>

The current max value for setting GF\_MAX\_HOR\_DIST and GF\_MAX\_VER\_DIST is 10000m in QGroundControl. Is there a reason for using 10000m as a limitation? Is it ok to extend this value to larger values?

---

## [VertexFly – Flutter-Based UAV Ground Control Station with Real-World 3D Maps](https://discuss.px4.io/t/vertexfly-flutter-based-uav-ground-control-station-with-real-world-3d-maps/49733)

<div class="topic-metadata">

**Author:** [@ahmet\_arif\_altintas](https://discuss.px4.io/u/ahmet_arif_altintas)\
**Replies:** 0\
**Last updated:** [November 7, 2026, 7:53pm UTC](https://discuss.px4.io/t/vertexfly-flutter-based-uav-ground-control-station-with-real-world-3d-maps/49733 "2026-11-07T19:53:58Z")

</div>

Hello PX4 Community! I’d like to introduce VertexFly, an independent UAV Ground Control Station (GCS) application I’ve been developing. Built with Flutter and MAVLink, VertexFly provides real-time flight monitoring, mi…

---

## [Complement of GPIO\_PUPD\_MASK](https://discuss.px4.io/t/complement-of-gpio-pupd-mask/49736)

<div class="topic-metadata">

**Author:** [@Hakan](https://discuss.px4.io/u/Hakan)\
**Replies:** 2\
**Last updated:** [November 9, 2026, 4:39pm UTC](https://discuss.px4.io/t/complement-of-gpio-pupd-mask/49736 "2026-11-09T16:39:10Z")

</div>

In the bootloader main.c for Ver. 1.18, shouldn’t there be a tilde (~) before GPIO\_PUPD\_MASK in the following function: px4\_arch\_configgpio((GPIO\_OTGFS\_VBUS & GPIO\_PUPD\_MASK) | GPIO\_FLOAT);?

---

## [iPad can't connect](https://discuss.px4.io/t/ipad-cant-connect/49665)

<div class="topic-metadata">

**Author:** [@rkcustomhomes](https://discuss.px4.io/u/rkcustomhomes)\
**Replies:** 3\
**Last updated:** [November 4, 2026, 5:23am UTC](https://discuss.px4.io/t/ipad-cant-connect/49665 "2026-11-04T05:23:28Z")

</div>

I’ve tried with my wifly that connects and works with my Mac but when I connect to the wifly network with my iPad it connects okay but QGround control never seems to see it. Any suggestions ?

---

## [VTOL Failing to Transition to Fixed Wing](https://discuss.px4.io/t/vtol-failing-to-transition-to-fixed-wing/49643)

<div class="topic-metadata">

**Author:** [@derek](https://discuss.px4.io/u/derek)\
**Replies:** 3\
**Last updated:** [November 4, 2026, 5:24am UTC](https://discuss.px4.io/t/vtol-failing-to-transition-to-fixed-wing/49643 "2026-11-04T05:24:26Z")

</div>

Hello! I am having an issue with a custom VTOL airframe, it is failing to transition to fixed wing due to not meeting the transition minimum airspeed. I have swapped our airspeed sensor and re-calibrated multiple times. …

---

## [Quick swap between RC and Mavlink control](https://discuss.px4.io/t/quick-swap-between-rc-and-mavlink-control/49794)

<div class="topic-metadata">

**Author:** [@tysweat0](https://discuss.px4.io/u/tysweat0)\
**Replies:** 4\
**Last updated:** [November 16, 2026, 1:30am UTC](https://discuss.px4.io/t/quick-swap-between-rc-and-mavlink-control/49794 "2026-11-16T01:30:30Z")

</div>

I want to test controlling my multirotor over an internet link. I want to be able to take over with the RC transmitter if anything weird happens during the first test. I want to set the input so that RC is first priority…

---

## [Tutorial: UOM Registration and Activation with QGroundControl and PX4](https://discuss.px4.io/t/tutorial-uom-registration-and-activation-with-qgroundcontrol-and-px4/49681)

<div class="topic-metadata">

**Author:** [@gfLv\_amov](https://discuss.px4.io/u/gfLv_amov)\
**Replies:** 2\
**Last updated:** [November 3, 2026, 3:54am UTC](https://discuss.px4.io/t/tutorial-uom-registration-and-activation-with-qgroundcontrol-and-px4/49681 "2026-11-03T03:54:04Z")

</div>

Hi everyone, I’m sharing a UOM registration-verification and activation workflow that we integrated into a Linux QGroundControl build, together with a test flight controller and Remote ID (RID) firmware. We used the UO…

---

## [Gazebo\_boat Alternative?](https://discuss.px4.io/t/gazebo-boat-alternative/49642)

<div class="topic-metadata">

**Author:** [@Bob\_Kidd](https://discuss.px4.io/u/Bob_Kidd)\
**Replies:** 3\
**Last updated:** [October 27, 2026, 10:35pm UTC](https://discuss.px4.io/t/gazebo-boat-alternative/49642 "2026-10-27T22:35:57Z")

</div>

Hello, Years ago, I had been doing research with surface vessels that were based off of the USV for gazebo\_boat inside the simulator. This was back when the repo was “Firmware” instead of PX4-Autopilot if that gives you…

---

## [Running Unmodified PX4 Firmware on Emulated Pixhawk 4 and 6C Boards (Athrill CPU Emulator)](https://discuss.px4.io/t/running-unmodified-px4-firmware-on-emulated-pixhawk-4-and-6c-boards-athrill-cpu-emulator/50039)

<div class="topic-metadata">

**Author:** [@tmori](https://discuss.px4.io/u/tmori)\
**Replies:** 0\
**Last updated:** [November 17, 2026, 10:07pm UTC](https://discuss.px4.io/t/running-unmodified-px4-firmware-on-emulated-pixhawk-4-and-6c-boards-athrill-cpu-emulator/50039 "2026-11-17T22:07:14Z")

</div>

Hello, I’m Takashi, developer of Athrill’s STM32 target and founder of Hakoniwa Lab, a small simulation company in Japan. I’ve been working on running PX4 firmware directly on an emulated STM32 MCU, without modifying PX…

---

## [PixHawk 6x, board v2 with PX4 v1.17 and 4in1 ECS](https://discuss.px4.io/t/pixhawk-6x-board-v2-with-px4-v1-17-and-4in1-ecs/49757)

<div class="topic-metadata">

**Author:** [@nebsar](https://discuss.px4.io/u/nebsar)\
**Replies:** 3\
**Last updated:** [November 15, 2026, 3:45am UTC](https://discuss.px4.io/t/pixhawk-6x-board-v2-with-px4-v1-17-and-4in1-ecs/49757 "2026-11-15T03:45:54Z")

</div>

I have PixHawk 6X on board v2 with Px4 v1.17. I want to use a budget 4in1 ECS for my VTOL drone’s multi-rotor motors. Is Velox V50A suitable to use? Or which one should I use? How will I do the wiring? PixHawk board v2 h…

---

## [Failure to Ascend](https://discuss.px4.io/t/failure-to-ascend/49641)

<div class="topic-metadata">

**Author:** [@swere](https://discuss.px4.io/u/swere)\
**Replies:** 2\
**Last updated:** [October 27, 2026, 5:44am UTC](https://discuss.px4.io/t/failure-to-ascend/49641 "2026-10-27T05:44:32Z")

</div>

Dear community, Please revise my log via the link. Drone has failed to ascend Thank you.

---

## [From a street address to a PX4 .plan in the browser: one finished plan to read, no account (owner post)](https://discuss.px4.io/t/from-a-street-address-to-a-px4-plan-in-the-browser-one-finished-plan-to-read-no-account-owner-post/49726)

<div class="topic-metadata">

**Author:** [@pro4aerials](https://discuss.px4.io/u/pro4aerials)\
**Replies:** 4\
**Last updated:** [November 16, 2026, 2:32pm UTC](https://discuss.px4.io/t/from-a-street-address-to-a-px4-plan-in-the-browser-one-finished-plan-to-read-no-account-owner-post/49726 "2026-11-16T14:32:35Z")

</div>

Hello, I’m Marc, owner of FlightDronePlan and of a small drone services company in Florida. Posting as the maker, per the Spotlight rules. Where it stands, up front: PX4 missions are tested in PX4 SITL only so far, not …

---

## [Can a Tiny Drone Navigate Home Without a Map? What Role Does LiDAR Play?](https://discuss.px4.io/t/can-a-tiny-drone-navigate-home-without-a-map-what-role-does-lidar-play/49650)

<div class="topic-metadata">

**Author:** [@benewakelidar](https://discuss.px4.io/u/benewakelidar)\
**Replies:** 1\
**Last updated:** [October 28, 2026, 12:34pm UTC](https://discuss.px4.io/t/can-a-tiny-drone-navigate-home-without-a-map-what-role-does-lidar-play/49650 "2026-10-28T12:34:29Z")

</div>

Small drones face a fundamental challenge: autonomous navigation often demands significant computing power, yet onboard processing capacity, memory, and energy are extremely limited. A recent study, Efficient Robot Navi…

---

## [Actuator Yaw is non-zero when hovering](https://discuss.px4.io/t/actuator-yaw-is-non-zero-when-hovering/50026)

<div class="topic-metadata">

**Author:** [@Hiran\_Bandarigoda](https://discuss.px4.io/u/Hiran_Bandarigoda)\
**Replies:** 4\
**Last updated:** [November 20, 2026, 4:14am UTC](https://discuss.px4.io/t/actuator-yaw-is-non-zero-when-hovering/50026 "2026-11-20T04:14:22Z")

</div>

Hi, I observed that when the drone is Hovering, the actuator Yaw is commanding the drone and in addition to that one diagonal motor pair is having rpm higher than other pair (RPM data in the log). So, as far as I under…

---

## [QGroundControl v5.1.5 on Windows 10: COM port selection resets and Flash button becomes disabled](https://discuss.px4.io/t/qgroundcontrol-v5-1-5-on-windows-10-com-port-selection-resets-and-flash-button-becomes-disabled/49686)

<div class="topic-metadata">

**Author:** [@gfLv\_amov](https://discuss.px4.io/u/gfLv_amov)\
**Replies:** 1\
**Last updated:** [November 4, 2026, 5:48am UTC](https://discuss.px4.io/t/qgroundcontrol-v5-1-5-on-windows-10-com-port-selection-resets-and-flash-button-becomes-disabled/49686 "2026-11-04T05:48:11Z")

</div>

Hi everyone, I’m trying to flash PX4 firmware onto a flight controller over USB on Windows 10. On QGroundControl’s Firmware page, I can select the port, but the selection clears before I can start flashing. I downloade…

---

## [WARN \[load\_mon\] dataman low on stack! (244 bytes left)](https://discuss.px4.io/t/warn-load-mon-dataman-low-on-stack-244-bytes-left/49993)

<div class="topic-metadata">

**Author:** [@williamtsai.417](https://discuss.px4.io/u/williamtsai.417)\
**Replies:** 3\
**Last updated:** [November 21, 2026, 6:50am UTC](https://discuss.px4.io/t/warn-load-mon-dataman-low-on-stack-244-bytes-left/49993 "2026-11-21T06:50:56Z")

</div>

Greetings, I encountered this warning often and I don’t know why. Seems like the dataman is the used to pull the flight plan from flight controller storage to RAM? While running the mission, the dataman’s writes and rea…

---

## [How do you catch hardware-assumption bugs in firmware before flashing?](https://discuss.px4.io/t/how-do-you-catch-hardware-assumption-bugs-in-firmware-before-flashing/49777)

<div class="topic-metadata">

**Author:** [@lainx06](https://discuss.px4.io/u/lainx06)\
**Replies:** 2\
**Last updated:** [November 15, 2026, 6:11pm UTC](https://discuss.px4.io/t/how-do-you-catch-hardware-assumption-bugs-in-firmware-before-flashing/49777 "2026-11-15T18:11:44Z")

</div>

Hi all, I’m a CS student researching how firmware engineers catch bugs that come from wrong assumptions about the hardware (wrong pin or peripheral mapping, board configuration mismatches, actuator or electrical limits)…

---

## [Anyone tried using fiber optic video transmission on an FPV drone?](https://discuss.px4.io/t/anyone-tried-using-fiber-optic-video-transmission-on-an-fpv-drone/49781)

<div class="topic-metadata">

**Author:** [@ha\_yang](https://discuss.px4.io/u/ha_yang)\
**Replies:** 2\
**Last updated:** [November 15, 2026, 11:40am UTC](https://discuss.px4.io/t/anyone-tried-using-fiber-optic-video-transmission-on-an-fpv-drone/49781 "2026-11-15T11:40:09Z")

</div>

I’ve been looking into fiber optic links instead of traditional wireless video transmission. I’m curious how difficult they are to set up and whether they work reliably on a custom FPV build.

---

## [Facing a video streaming issue in QGC 5.1.5](https://discuss.px4.io/t/facing-a-video-streaming-issue-in-qgc-5-1-5/49768)

<div class="topic-metadata">

**Author:** [@rufeed](https://discuss.px4.io/u/rufeed)\
**Replies:** 1\
**Last updated:** [November 11, 2026, 3:00am UTC](https://discuss.px4.io/t/facing-a-video-streaming-issue-in-qgc-5-1-5/49768 "2026-11-11T03:00:05Z")

</div>

Facing a video streaming issue in QGC 5.1.5. The RTSP stream (H.264, TCP) is working in VLC and QGC 5.0, but QGC 5.1.5 is showing “Waiting for Video”. Tested with the camera connected directly to the PC via Ethernet. Ha…

---

## [PX4 Dev Call: Oct 28, 2026 (Team sync, and Community Q&A)](https://discuss.px4.io/t/px4-dev-call-oct-28-2026-team-sync-and-community-q-a/49639)

<div class="topic-metadata">

**Author:** [@system](https://discuss.px4.io/u/system)\
**Replies:** 1\
**Last updated:** [October 30, 2026, 5:11am UTC](https://discuss.px4.io/t/px4-dev-call-oct-28-2026-team-sync-and-community-q-a/49639 "2026-10-30T05:11:26Z")

</div>

PX4 Sync / Q&A - 2026-10-28T16:00:00Z (UTC) This week: 81 PRs merged | 210 awaiting review | 0 new bugs Announcements Events Dev Call Items None Release Updates: Issues: Decisions: PRs Merged This Week 81 PRs …

---

## [PX4 Dev Call: Nov 11, 2026 (Team sync, and Community Q&A)](https://discuss.px4.io/t/px4-dev-call-nov-11-2026-team-sync-and-community-q-a/49749)

<div class="topic-metadata">

**Author:** [@system](https://discuss.px4.io/u/system)\
**Replies:** 0\
**Last updated:** [November 9, 2026, 10:01am UTC](https://discuss.px4.io/t/px4-dev-call-nov-11-2026-team-sync-and-community-q-a/49749 "2026-11-09T10:01:10Z")

</div>

PX4 Sync / Q&A - 2026-11-11T16:00:00Z (UTC) This week: 68 PRs merged | 212 awaiting review | 0 new bugs Announcements Events Dev Call Items Geofence Updates discussion by @JonasPerolini Release Updates: Issues…

---

## [Cube Orange Not Communicating Properly with GCS](https://discuss.px4.io/t/cube-orange-not-communicating-properly-with-gcs/49691)

<div class="topic-metadata">

**Author:** [@DTRON](https://discuss.px4.io/u/DTRON)\
**Replies:** 1\
**Last updated:** [November 4, 2026, 5:33am UTC](https://discuss.px4.io/t/cube-orange-not-communicating-properly-with-gcs/49691 "2026-11-04T05:33:21Z")

</div>

To start with we are using an off the shelf drone that comes with a proprietary 2.4 Ghz radio and then another RFD900X radio. The RFD is used to connect to a proprietary GCS that is just a reskinned QGC software with som…

---

## [Can Three LiDAR Sensors Simplify Obstacle Avoidance for Small Drones?](https://discuss.px4.io/t/can-three-lidar-sensors-simplify-obstacle-avoidance-for-small-drones/49717)

<div class="topic-metadata">

**Author:** [@benewakelidar](https://discuss.px4.io/u/benewakelidar)\
**Replies:** 0\
**Last updated:** [November 6, 2026, 8:43am UTC](https://discuss.px4.io/t/can-three-lidar-sensors-simplify-obstacle-avoidance-for-small-drones/49717 "2026-11-06T08:43:59Z")

</div>

Real-time obstacle avoidance is a tricky problem for small autonomous drones. Onboard computing power is limited, but the aircraft still needs to detect obstacles and react quickly enough to avoid them. Depth cameras ar…

---

## [QGC Expert for Drone Setup wanted in Brazil](https://discuss.px4.io/t/qgc-expert-for-drone-setup-wanted-in-brazil/50116)

<div class="topic-metadata">

**Author:** [@peterschi](https://discuss.px4.io/u/peterschi)\
**Replies:** 2\
**Last updated:** [November 22, 2026, 12:11am UTC](https://discuss.px4.io/t/qgc-expert-for-drone-setup-wanted-in-brazil/50116 "2026-11-22T00:11:42Z")

</div>

Dear all, I am searching for PX4 / QGC experts to help us get a X650 drone into the air in Brazil, Mato Grosso. Ideally with the time and ability to help us set things up on site. We are at 80% but need help with the la…

---

## [\[Hiring\] State Estimation Engineer (EKF / Sensor Fusion) – UAV autopilot – Gurugram, India (on-site)](https://discuss.px4.io/t/hiring-state-estimation-engineer-ekf-sensor-fusion-uav-autopilot-gurugram-india-on-site/49729)

<div class="topic-metadata">

**Author:** [@Konark\_Sharma](https://discuss.px4.io/u/Konark_Sharma)\
**Replies:** 0\
**Last updated:** [November 7, 2026, 2:57pm UTC](https://discuss.px4.io/t/hiring-state-estimation-engineer-ekf-sensor-fusion-uav-autopilot-gurugram-india-on-site/49729 "2026-11-07T14:57:08Z")

</div>

Hi everyone, I’m Konark, Project Head of the Indigenous Flight Controller Development Program at Flybots Tech Services in Gurugram, India. We’re building our own UAV autopilot, and we’re hiring someone to own its naviga…

---

## [ArduPilot Firmware Developer (Code Modification & Custom Logic)](https://discuss.px4.io/t/ardupilot-firmware-developer-code-modification-custom-logic/49796)

<div class="topic-metadata">

**Author:** [@waiphyo\_maung](https://discuss.px4.io/u/waiphyo_maung)\
**Replies:** 0\
**Last updated:** [November 11, 2026, 3:52pm UTC](https://discuss.px4.io/t/ardupilot-firmware-developer-code-modification-custom-logic/49796 "2026-11-11T15:52:23Z")

</div>

I am an embedded firmware developer focusing strictly on ArduPilot source code modification, custom firmware builds, and simulation testing. I work with ArduCopter and ArduPlane platforms using C/C++ to implement custom …

---

## [Plans to upstream zenoh-pico support to nuttx-apps?](https://discuss.px4.io/t/plans-to-upstream-zenoh-pico-support-to-nuttx-apps/50128)

<div class="topic-metadata">

**Author:** [@mdurnea4](https://discuss.px4.io/u/mdurnea4)\
**Replies:** 1\
**Last updated:** [November 22, 2026, 6:21am UTC](https://discuss.px4.io/t/plans-to-upstream-zenoh-pico-support-to-nuttx-apps/50128 "2026-11-22T06:21:57Z")

</div>

Hi, I’m a CS student at Politehnica Bucharest working on my bachelor thesis: packaging zenoh-pico for NuttX as a package in nuttx-apps, validated on ESP32. I saw that PX4 already runs zenoh-pico on NuttX. Do you have an…

---

## [Robotics and control engineer for remote contract work](https://discuss.px4.io/t/robotics-and-control-engineer-for-remote-contract-work/49779)

<div class="topic-metadata">

**Author:** [@Joosep](https://discuss.px4.io/u/Joosep)\
**Replies:** 0\
**Last updated:** [November 11, 2026, 3:54am UTC](https://discuss.px4.io/t/robotics-and-control-engineer-for-remote-contract-work/49779 "2026-11-11T03:54:01Z")

</div>

Hello, I’m a robotics and instrumentation engineer, background in control systems for scientific research, from the UK, and available for remote contract work, part or full time. I am also open to roles as technical lea…

---

## [Want to understand the working of drones , especially its communication and networking part](https://discuss.px4.io/t/want-to-understand-the-working-of-drones-especially-its-communication-and-networking-part/49767)

<div class="topic-metadata">

**Author:** [@shubham-Alhat](https://discuss.px4.io/u/shubham-Alhat)\
**Replies:** 0\
**Last updated:** [November 10, 2026, 1:50pm UTC](https://discuss.px4.io/t/want-to-understand-the-working-of-drones-especially-its-communication-and-networking-part/49767 "2026-11-10T13:50:42Z")

</div>

here i want to know, how actually drones can send the data to its ground control system or any client sitting far away. (assume 10 to 30KM away). like sending telemetry data and video tracks if avaiable??? which protocol…

---

## [VAK Industries: Looking for "Principal Investigator (Aerospace/Mechanical Engineer), Navy SBIR" for a "part-time now, full-time on award" position, "remote / Missouri"](https://discuss.px4.io/t/vak-industries-looking-for-principal-investigator-aerospace-mechanical-engineer-navy-sbir-for-a-part-time-now-full-time-on-award-position-remote-missouri/49775)

<div class="topic-metadata">

**Author:** [@Isaiah\_Vakulich](https://discuss.px4.io/u/Isaiah_Vakulich)\
**Replies:** 0\
**Last updated:** [November 11, 2026, 3:51am UTC](https://discuss.px4.io/t/vak-industries-looking-for-principal-investigator-aerospace-mechanical-engineer-navy-sbir-for-a-part-time-now-full-time-on-award-position-remote-missouri/49775 "2026-11-11T03:51:24Z")

</div>

VAK Industries LLC is a new Missouri company preparing a Phase I proposal for Navy SBIR topic DON27BZ02-NV022, “Collapsible Fixed-Wing Low-Cost UAS for ISR” (proposals due Jan 6, 2027). I’m the founder, 16 years old, an…

---

## [RunSpotlighttime governance above PX4/MAVLink — where should the governance boundary sit?](https://discuss.px4.io/t/runspotlighttime-governance-above-px4-mavlink-where-should-the-governance-boundary-sit/49926)

<div class="topic-metadata">

**Author:** [@AndreasBlumer](https://discuss.px4.io/u/AndreasBlumer)\
**Replies:** 0\
**Last updated:** [November 15, 2026, 5:35am UTC](https://discuss.px4.io/t/runspotlighttime-governance-above-px4-mavlink-where-should-the-governance-boundary-sit/49926 "2026-11-15T05:35:24Z")

</div>

I’m exploring an architectural question around increasingly autonomous and multi-vehicle operations: Where should changing operational constraints be handled in a PX4-based system? PX4 already provides extensive vehicl…

[Next page](https://discuss.px4.io/top.md?page=1&per_page=50)
